Peptide Chemistry

What is Melanotan II? Sequence, formula and molecular weight

By the NexXGen Research Team · Updated November 21, 2026 · 4 min read

Key takeaways

  • Melanotan II is a synthetic cyclic peptide of seven residues.
  • It is written Ac-Nle-cyclo(Asp-His-D-Phe-Arg-Trp-Lys)-NH2.
  • Molecular formula C50H69N15O9, molecular weight about 1024.2 g/mol, CAS number 121062-08-6.
  • A lab report gives purity by HPLC. Some also give the amount per vial or a mass for identity, so read what the report for your lot shows.
  • For in-vitro, laboratory research use only.

Melanotan II is a synthetic peptide of seven residues, six of them closed into a ring: Ac-Nle-cyclo(Asp-His-D-Phe-Arg-Trp-Lys)-NH2. Its molecular formula is C50H69N15O9, its molecular weight is about 1024.2 g/mol, and its CAS number is 121062-08-6.

This guide gives laboratory staff the compound’s identifiers and the values to expect on an analytical report. NexXGen Peptides lists it as lyophilized powder in one size: Melanotan II 10 mg.

What is the sequence of Melanotan II?

The seven residues run from norleucine at the N-terminus to lysine at the C-terminus, and each appears once. Nle is norleucine, a non-standard residue. D-Phe is D-phenylalanine, the only D-amino acid in the chain. The other five are aspartic acid, histidine, arginine, tryptophan and lysine.

In one-letter code it is XDHFRWK, where X stands for norleucine and F for D-phenylalanine. The one-letter form leaves out the acetyl group, the amide and the ring.

What do Ac, cyclo and NH2 mean in the sequence?

Three marks in the written form are not residues. Ac, at the start, is an acetyl group on the N-terminus. NH2, at the end, marks a C-terminal amide. Cyclo, with its brackets, marks a ring: an amide (lactam) bond between the side chains of aspartic acid at position 2 and lysine at position 7 closes the six residues in brackets into a ring. Norleucine, at position 1, stays outside it.

Two points matter in the lab. There is no cysteine, so the peptide forms no disulfide bonds; the ring is closed by that side-chain amide bond alone. The chain holds one tryptophan residue, which decides how it is detected on HPLC.

What are the molecular formula and molecular weight of Melanotan II?

The formula counts 50 carbon, 69 hydrogen, 15 nitrogen and 9 oxygen atoms. It is the formula of the whole compound, with the acetyl group, the amide end and the ring bond in place. The average molecular weight is about 1024.2 g/mol. Our product page shows 1024.198; small differences between sources come from rounding.

The monoisotopic mass is 1023.54 Da. A mass spectrum is checked against that figure, or against the average weight, depending on how the laboratory reports it.

Both figures describe the peptide alone. Synthetic peptides are often supplied as a salt, commonly acetate or trifluoroacetate, and the powder also holds some water. The mass of powder in a vial and the mass of peptide are therefore not the same number.

What should Melanotan II look like on an analytical report?

TestWhat it confirmsWhat to expect for this sequence
Mass spectrometry, when reportedIdentityA figure that fits the peptide, monoisotopic or average. Calculated electrospray ions: about m/z 1024.55 (one charge) and 512.78 (two charges)
HPLC with UV detectionPurityOne dominant peak, read at about 214 to 220 nm. Tryptophan also absorbs at about 280 nm, so that wavelength can be used as well
Content, when reportedAmount of peptide in the vialA figure in mg to compare with the size on the label
Net peptide content, when reportedShare of the powder that is peptideA percentage below 100, because salt and water are part of the powder
AppearancePhysical formLyophilized powder

The report for the lot in hand is the source of truth. Posted reports are on the Certificates of Analysis page.

What should a researcher check?

  • Name and size. The compound and size on the report match the label.
  • Lot number. The lot or batch on the vial is the one on the report.
  • Purity. The report gives an HPLC purity figure for that lot.
  • Mass, where the report gives one. It agrees with the values in the table above.

Research compound in this article

Melanotan II 10 mg

Lyophilized powder

Research-use note

All NexXGen Peptides compounds are intended strictly for in-vitro research, laboratory and analytical purposes. They are not for human or animal use and must be handled only by qualified researchers aged 21 or older. Nothing in this article is medical advice.

Frequently asked questions

How many amino acids are in Melanotan II?

Seven, all different. Six of them form the ring.

What is the CAS number for Melanotan II?

121062-08-6.

Is the molecular weight of Melanotan II the same as its monoisotopic mass?

No. The average molecular weight counts every isotope in its natural proportion. The monoisotopic mass counts only the most common isotope of each element, so it is slightly lower. For Melanotan II the gap is about 0.7: 1024.2 against 1023.54.

Can Melanotan II be read at 280 nm on HPLC?

Yes. One residue in the sequence absorbs at about that wavelength: tryptophan. Detection can also rely on the peptide bonds, which absorb at about 214 to 220 nm.

Does Melanotan II contain disulfide bonds?

No. The sequence has no cysteine. Its ring is closed by an amide bond between two side chains.

Browse all research compounds →