Peptide Chemistry
What is Melanotan II? Sequence, formula and molecular weight
By the NexXGen Research Team · Updated November 21, 2026 · 4 min read
Key takeaways
- Melanotan II is a synthetic cyclic peptide of seven residues.
- It is written Ac-Nle-cyclo(Asp-His-D-Phe-Arg-Trp-Lys)-NH2.
- Molecular formula C50H69N15O9, molecular weight about 1024.2 g/mol, CAS number 121062-08-6.
- A lab report gives purity by HPLC. Some also give the amount per vial or a mass for identity, so read what the report for your lot shows.
- For in-vitro, laboratory research use only.
Melanotan II is a synthetic peptide of seven residues, six of them closed into a ring: Ac-Nle-cyclo(Asp-His-D-Phe-Arg-Trp-Lys)-NH2. Its molecular formula is C50H69N15O9, its molecular weight is about 1024.2 g/mol, and its CAS number is 121062-08-6.
This guide gives laboratory staff the compound’s identifiers and the values to expect on an analytical report. NexXGen Peptides lists it as lyophilized powder in one size: Melanotan II 10 mg.
What is the sequence of Melanotan II?
The seven residues run from norleucine at the N-terminus to lysine at the C-terminus, and each appears once. Nle is norleucine, a non-standard residue. D-Phe is D-phenylalanine, the only D-amino acid in the chain. The other five are aspartic acid, histidine, arginine, tryptophan and lysine.
In one-letter code it is XDHFRWK, where X stands for norleucine and F for D-phenylalanine. The one-letter form leaves out the acetyl group, the amide and the ring.
What do Ac, cyclo and NH2 mean in the sequence?
Three marks in the written form are not residues. Ac, at the start, is an acetyl group on the N-terminus. NH2, at the end, marks a C-terminal amide. Cyclo, with its brackets, marks a ring: an amide (lactam) bond between the side chains of aspartic acid at position 2 and lysine at position 7 closes the six residues in brackets into a ring. Norleucine, at position 1, stays outside it.
Two points matter in the lab. There is no cysteine, so the peptide forms no disulfide bonds; the ring is closed by that side-chain amide bond alone. The chain holds one tryptophan residue, which decides how it is detected on HPLC.
What are the molecular formula and molecular weight of Melanotan II?
The formula counts 50 carbon, 69 hydrogen, 15 nitrogen and 9 oxygen atoms. It is the formula of the whole compound, with the acetyl group, the amide end and the ring bond in place. The average molecular weight is about 1024.2 g/mol. Our product page shows 1024.198; small differences between sources come from rounding.
The monoisotopic mass is 1023.54 Da. A mass spectrum is checked against that figure, or against the average weight, depending on how the laboratory reports it.
Both figures describe the peptide alone. Synthetic peptides are often supplied as a salt, commonly acetate or trifluoroacetate, and the powder also holds some water. The mass of powder in a vial and the mass of peptide are therefore not the same number.
What should Melanotan II look like on an analytical report?
| Test | What it confirms | What to expect for this sequence |
|---|---|---|
| Mass spectrometry, when reported | Identity | A figure that fits the peptide, monoisotopic or average. Calculated electrospray ions: about m/z 1024.55 (one charge) and 512.78 (two charges) |
| HPLC with UV detection | Purity | One dominant peak, read at about 214 to 220 nm. Tryptophan also absorbs at about 280 nm, so that wavelength can be used as well |
| Content, when reported | Amount of peptide in the vial | A figure in mg to compare with the size on the label |
| Net peptide content, when reported | Share of the powder that is peptide | A percentage below 100, because salt and water are part of the powder |
| Appearance | Physical form | Lyophilized powder |
The report for the lot in hand is the source of truth. Posted reports are on the Certificates of Analysis page.
What should a researcher check?
- Name and size. The compound and size on the report match the label.
- Lot number. The lot or batch on the vial is the one on the report.
- Purity. The report gives an HPLC purity figure for that lot.
- Mass, where the report gives one. It agrees with the values in the table above.
Research-use note
All NexXGen Peptides compounds are intended strictly for in-vitro research, laboratory and analytical purposes. They are not for human or animal use and must be handled only by qualified researchers aged 21 or older. Nothing in this article is medical advice.
Frequently asked questions
How many amino acids are in Melanotan II?
Seven, all different. Six of them form the ring.
What is the CAS number for Melanotan II?
121062-08-6.
Is the molecular weight of Melanotan II the same as its monoisotopic mass?
No. The average molecular weight counts every isotope in its natural proportion. The monoisotopic mass counts only the most common isotope of each element, so it is slightly lower. For Melanotan II the gap is about 0.7: 1024.2 against 1023.54.
Can Melanotan II be read at 280 nm on HPLC?
Yes. One residue in the sequence absorbs at about that wavelength: tryptophan. Detection can also rely on the peptide bonds, which absorb at about 214 to 220 nm.
Does Melanotan II contain disulfide bonds?
No. The sequence has no cysteine. Its ring is closed by an amide bond between two side chains.
