Peptide Chemistry

What is MOTS-c? Sequence, formula and molecular weight

By the NexXGen Research Team · Updated November 17, 2026 · 4 min read

Key takeaways

  • MOTS-c is a synthetic peptide made of 16 amino acids.
  • In one-letter code its sequence is MRWQEMGYIFYPRKLR.
  • Molecular formula C101H152N28O22S2, molecular weight about 2174.6 g/mol, CAS number 1627580-64-6.
  • A lab report gives purity by HPLC. Some also give the amount per vial or a mass for identity, so read what the report for your lot shows.
  • For in-vitro, laboratory research use only.

MOTS-c is a synthetic peptide: a single chain of 16 amino acids with the sequence Met-Arg-Trp-Gln-Glu-Met-Gly-Tyr-Ile-Phe-Tyr-Pro-Arg-Lys-Leu-Arg. Its molecular formula is C101H152N28O22S2, its molecular weight is about 2174.6 g/mol, and its CAS number is 1627580-64-6.

This guide gives laboratory staff the compound’s identifiers, the values to expect on an analytical report, and storage notes for the lyophilized powder. NexXGen Peptides lists it as lyophilized powder in one size: MOTS-c 10 mg.

What is the amino acid sequence of MOTS-c?

The 16 residues run from methionine at the N-terminus to arginine at the C-terminus. Three of them are arginine, at positions 2, 13 and 16. Two are methionine, at positions 1 and 6, and two are tyrosine, at positions 8 and 11. The other nine appear once each: tryptophan, glutamine, glutamic acid, glycine, isoleucine, phenylalanine, proline, lysine and leucine.

Two points matter in the lab. There is no cysteine, so the peptide forms no disulfide bonds and stays a single linear chain. The chain does hold one tryptophan and two tyrosine residues, which decides how it is detected on HPLC.

What are the molecular formula and molecular weight of MOTS-c?

The formula counts 101 carbon, 152 hydrogen, 28 nitrogen, 22 oxygen and 2 sulfur atoms. The average molecular weight is about 2174.6 g/mol. Our product page shows 2174.64; small differences between sources come from rounding.

The monoisotopic mass is 2173.11 Da. A mass spectrum is checked against that figure, or against the average weight, depending on how the laboratory reports it.

Both figures describe the peptide alone. Synthetic peptides are often supplied as a salt, commonly acetate or trifluoroacetate, and the powder also holds some water. The mass of powder in a vial and the mass of peptide are therefore not the same number.

What should MOTS-c look like on an analytical report?

TestWhat it confirmsWhat to expect for this sequence
Mass spectrometry, when reportedIdentityA figure that fits the peptide, monoisotopic or average. Calculated electrospray ions: about m/z 2174.12 (one charge), 1087.56 (two charges) and 725.38 (three charges)
HPLC with UV detectionPurityOne dominant peak, read at about 214 to 220 nm. Tryptophan and tyrosine also absorb at about 280 nm, so that wavelength can be used as well
Content, when reportedAmount of peptide in the vialA figure in mg to compare with the size on the label
Net peptide content, when reportedShare of the powder that is peptideA percentage below 100, because salt and water are part of the powder
AppearancePhysical formLyophilized powder. Our product page describes a solid, white powder

The report for the lot in hand is the source of truth. Posted reports are on the Certificates of Analysis page.

How should lyophilized MOTS-c be stored?

The listing is 10 mg of lyophilized powder in a 3 mL glass vial. Our product page gives storage at 25°C or below, away from heat, light and moisture. Keep the vial sealed between openings.

What should a researcher check?

  • Name and size. The compound and size on the report match the label.
  • Lot number. The lot or batch on the vial is the one on the report.
  • Purity. The report gives an HPLC purity figure for that lot.
  • Mass, where the report gives one. It agrees with the values in the table above.

Research compound in this article

MOTS-c 10 mg

Lyophilized powder

Research-use note

All NexXGen Peptides compounds are intended strictly for in-vitro research, laboratory and analytical purposes. They are not for human or animal use and must be handled only by qualified researchers aged 21 or older. Nothing in this article is medical advice.

Frequently asked questions

How many amino acids are in MOTS-c?

Sixteen. Twelve different amino acids make up the chain, because arginine, methionine and tyrosine each appear more than once.

What is the CAS number for MOTS-c?

1627580-64-6.

Is the molecular weight of MOTS-c the same as its monoisotopic mass?

No. The average molecular weight counts every isotope in its natural proportion. The monoisotopic mass counts only the most common isotope of each element, so it is slightly lower. For MOTS-c the gap is about 1.5: 2174.6 against 2173.11.

Can MOTS-c be read at 280 nm on HPLC?

Yes. Three residues in the sequence absorb at about that wavelength: one tryptophan and two tyrosines. Detection can also rely on the peptide bonds, which absorb at about 214 to 220 nm.

Does MOTS-c contain disulfide bonds?

No. The sequence has no cysteine, so the peptide is one linear chain.

Browse all research compounds →