Peptide Chemistry
What is AOD-9604? Sequence, formula and molecular weight
By the NexXGen Research Team · Updated November 20, 2026 · 4 min read
Key takeaways
- AOD-9604 is a synthetic peptide made of 16 amino acids.
- In one-letter code its sequence is YLRIVQCRSVEGSCGF.
- Molecular formula C78H123N23O23S2, molecular weight about 1815.1 g/mol, CAS number 221231-10-3.
- A lab report gives purity by HPLC. Some also give the amount per vial or a mass for identity, so read what the report for your lot shows.
- For in-vitro, laboratory research use only.
AOD-9604 is a synthetic peptide: a single chain of 16 amino acids with the sequence Tyr-Leu-Arg-Ile-Val-Gln-Cys-Arg-Ser-Val-Glu-Gly-Ser-Cys-Gly-Phe. Its molecular formula is C78H123N23O23S2, its molecular weight is about 1815.1 g/mol, and its CAS number is 221231-10-3.
This guide gives laboratory staff the compound’s identifiers, the values to expect on an analytical report, and storage notes for the lyophilized powder. NexXGen Peptides lists it as lyophilized powder in one size: AOD-9604 5 mg.
What is the amino acid sequence of AOD-9604?
The 16 residues run from tyrosine at the N-terminus to phenylalanine at the C-terminus. Five amino acids appear twice each: arginine at positions 3 and 8, valine at 5 and 10, cysteine at 7 and 14, serine at 9 and 13, and glycine at 12 and 15. The other six appear once each: tyrosine, leucine, isoleucine, glutamine, glutamic acid and phenylalanine. None of the residues is a D-amino acid.
Two points matter in the lab. One disulfide bond between the two cysteine residues closes part of the chain into a ring. The chain holds one tyrosine residue and no tryptophan, which decides how it is detected on HPLC.
What are the molecular formula and molecular weight of AOD-9604?
The formula counts 78 carbon, 123 hydrogen, 23 nitrogen, 23 oxygen and 2 sulfur atoms. Both sulfur atoms sit in the two cysteine residues, and the formula is that of the peptide with its disulfide bond in place. The average molecular weight is about 1815.1 g/mol. Our product page shows 1815.12; small differences between sources come from rounding.
The monoisotopic mass is 1813.86 Da. A mass spectrum is checked against that figure, or against the average weight, depending on how the laboratory reports it.
Both figures describe the peptide alone. Synthetic peptides are often supplied as a salt, commonly acetate or trifluoroacetate, and the powder also holds some water. The mass of powder in a vial and the mass of peptide are therefore not the same number.
What should AOD-9604 look like on an analytical report?
| Test | What it confirms | What to expect for this sequence |
|---|---|---|
| Mass spectrometry, when reported | Identity | A figure that fits the peptide, monoisotopic or average. Calculated electrospray ions: about m/z 1814.87 (one charge), 907.94 (two charges) and 605.63 (three charges) |
| HPLC with UV detection | Purity | One dominant peak, read at about 214 to 220 nm. AOD-9604 absorbs only weakly at about 280 nm |
| Content, when reported | Amount of peptide in the vial | A figure in mg to compare with the size on the label |
| Net peptide content, when reported | Share of the powder that is peptide | A percentage below 100, because salt and water are part of the powder |
| Appearance | Physical form | Lyophilized powder. Our product page describes a white powder |
The report for the lot in hand is the source of truth. Posted reports are on the Certificates of Analysis page.
How should lyophilized AOD-9604 be stored?
The listing is 5 mg of lyophilized powder in a 3 mL sealed vial. Our product page gives storage at 6°C or below, away from heat, light and moisture.
What should a researcher check?
- Name and size. The compound and size on the report match the label.
- Lot number. The lot or batch on the vial is the one on the report.
- Purity. The report gives an HPLC purity figure for that lot.
- Mass, where the report gives one. It agrees with the values in the table above.
Research-use note
All NexXGen Peptides compounds are intended strictly for in-vitro research, laboratory and analytical purposes. They are not for human or animal use and must be handled only by qualified researchers aged 21 or older. Nothing in this article is medical advice.
Frequently asked questions
How many amino acids are in AOD-9604?
Sixteen. Eleven different amino acids make up the chain, because five of them appear twice.
What is the CAS number for AOD-9604?
221231-10-3.
Is the molecular weight of AOD-9604 the same as its monoisotopic mass?
No. The average molecular weight counts every isotope in its natural proportion. The monoisotopic mass counts only the most common isotope of each element, so it is slightly lower. For AOD-9604 the gap is about 1.2: 1815.1 against 1813.86.
Can AOD-9604 be read at 280 nm on HPLC?
Only weakly. AOD-9604 has one tyrosine residue and no tryptophan, so its signal there is weak. Detection can rely on the peptide bonds, which absorb at about 214 to 220 nm.
Does AOD-9604 contain disulfide bonds?
Yes, one. It links the cysteine residues at positions 7 and 14.
