Peptide Chemistry

What is PT-141? Sequence, formula and molecular weight

By the NexXGen Research Team · Updated November 22, 2026 · 4 min read

Key takeaways

  • PT-141 is a synthetic cyclic peptide of seven residues.
  • It is written Ac-Nle-cyclo(Asp-His-D-Phe-Arg-Trp-Lys)-OH.
  • Molecular formula C50H68N14O10, molecular weight about 1025.2 g/mol, CAS number 189691-06-3.
  • A lab report gives purity by HPLC. Some also give the amount per vial or a mass for identity, so read what the report for your lot shows.
  • For in-vitro, laboratory research use only.

PT-141 is a synthetic peptide of seven residues, six of them closed into a ring: Ac-Nle-cyclo(Asp-His-D-Phe-Arg-Trp-Lys)-OH. Its molecular formula is C50H68N14O10, its molecular weight is about 1025.2 g/mol, and its CAS number is 189691-06-3.

This guide gives laboratory staff the compound’s identifiers, the values to expect on an analytical report, and storage notes for the lyophilized powder. NexXGen Peptides lists it as lyophilized powder in one size: PT-141 10 mg.

What is the sequence of PT-141?

The seven residues run from norleucine at the N-terminus to lysine at the C-terminus, and each appears once. Nle is norleucine, a non-standard residue. D-Phe is D-phenylalanine, the only D-amino acid in the chain. The other five are aspartic acid, histidine, arginine, tryptophan and lysine.

In one-letter code it is XDHFRWK, where X stands for norleucine and F for D-phenylalanine. The one-letter form leaves out the acetyl group and the ring.

What do Ac, cyclo and OH mean in the sequence?

Three marks in the written form are not residues. Ac, at the start, is an acetyl group on the N-terminus. OH, at the end, marks a free carboxylic acid at the C-terminus. Cyclo, with its brackets, marks a ring: an amide (lactam) bond between the side chains of aspartic acid at position 2 and lysine at position 7 closes the six residues in brackets into a ring. Norleucine, at position 1, stays outside it.

Two points matter in the lab. There is no cysteine, so the peptide forms no disulfide bonds; the ring is closed by that side-chain amide bond alone. The chain holds one tryptophan residue, which decides how it is detected on HPLC.

What are the molecular formula and molecular weight of PT-141?

The formula counts 50 carbon, 68 hydrogen, 14 nitrogen and 10 oxygen atoms. It is the formula of the whole compound, with the acetyl group, the free acid end and the ring bond in place. The average molecular weight is about 1025.2 g/mol.

The monoisotopic mass is 1024.52 Da. A mass spectrum is checked against that figure, or against the average weight, depending on how the laboratory reports it.

Both figures describe the peptide alone. Synthetic peptides are often supplied as a salt, commonly acetate or trifluoroacetate, and the powder also holds some water. The mass of powder in a vial and the mass of peptide are therefore not the same number.

What should PT-141 look like on an analytical report?

TestWhat it confirmsWhat to expect for this sequence
Mass spectrometry, when reportedIdentityA figure that fits the peptide, monoisotopic or average. Calculated electrospray ions: about m/z 1025.53 (one charge) and 513.27 (two charges)
HPLC with UV detectionPurityOne dominant peak, read at about 214 to 220 nm. Tryptophan also absorbs at about 280 nm, so that wavelength can be used as well
Content, when reportedAmount of peptide in the vialA figure in mg to compare with the size on the label
Net peptide content, when reportedShare of the powder that is peptideA percentage below 100, because salt and water are part of the powder
AppearancePhysical formLyophilized powder. Our product page describes a solid, white powder

The report for the lot in hand is the source of truth. Posted reports are on the Certificates of Analysis page.

How should lyophilized PT-141 be stored?

The listing is 10 mg of lyophilized powder in a 3 mL vial. Our product page gives storage at 20°C or below, away from heat, light and moisture. Keep the vial sealed between openings.

What should a researcher check?

  • Name and size. The compound and size on the report match the label.
  • Lot number. The lot or batch on the vial is the one on the report.
  • Purity. The report gives an HPLC purity figure for that lot.
  • Mass, where the report gives one. It agrees with the values in the table above.

Research compound in this article

PT-141 10 mg

Lyophilized powder

Research-use note

All NexXGen Peptides compounds are intended strictly for in-vitro research, laboratory and analytical purposes. They are not for human or animal use and must be handled only by qualified researchers aged 21 or older. Nothing in this article is medical advice.

Frequently asked questions

How many amino acids are in PT-141?

Seven, all different. Six of them form the ring.

What is the CAS number for PT-141?

189691-06-3.

Is the molecular weight of PT-141 the same as its monoisotopic mass?

No. The average molecular weight counts every isotope in its natural proportion. The monoisotopic mass counts only the most common isotope of each element, so it is slightly lower. For PT-141 the gap is about 0.7: 1025.2 against 1024.52.

Can PT-141 be read at 280 nm on HPLC?

Yes. One residue in the sequence absorbs at about that wavelength: tryptophan. Detection can also rely on the peptide bonds, which absorb at about 214 to 220 nm.

Does PT-141 contain disulfide bonds?

No. The sequence has no cysteine. Its ring is closed by an amide bond between two side chains.

Browse all research compounds →