Peptide Chemistry

What is Sermorelin? Sequence, formula and molecular weight

By the NexXGen Research Team · Updated November 19, 2026 · 4 min read

Key takeaways

  • Sermorelin is a synthetic peptide made of 29 amino acids.
  • It is a single linear chain ending in a C-terminal amide, with no disulfide bonds.
  • Molecular formula C149H246N44O42S, molecular weight about 3357.9 g/mol, CAS number 86168-78-7.
  • A lab report gives purity by HPLC. Some also give the amount per vial or a mass for identity, so read what the report for your lot shows.
  • For in-vitro, laboratory research use only.

Sermorelin is a synthetic peptide: a single chain of 29 amino acids. Its molecular formula is C149H246N44O42S, its molecular weight is about 3357.9 g/mol, and its CAS number is 86168-78-7.

This guide gives laboratory staff the compound’s identifiers, the values to expect on an analytical report, and storage notes for the lyophilized powder. NexXGen Peptides lists it as lyophilized powder in two sizes: Sermorelin 5 mg and Sermorelin 10 mg.

What is the amino acid sequence of Sermorelin?

In three-letter code the sequence is Tyr-Ala-Asp-Ala-Ile-Phe-Thr-Asn-Ser-Tyr-Arg-Lys-Val-Leu-Gly-Gln-Leu-Ser-Ala-Arg-Lys-Leu-Leu-Gln-Asp-Ile-Met-Ser-Arg-NH2. In one-letter code it is YADAIFTNSYRKVLGQLSARKLLQDIMSR. The chain ends in a C-terminal amide, written NH2.

The 29 residues run from tyrosine at the N-terminus to arginine at the C-terminus. Leucine appears four times, at positions 14, 17, 22 and 23. Alanine, serine and arginine appear three times each. Tyrosine, aspartic acid, isoleucine, lysine and glutamine appear twice each. The other six appear once each: phenylalanine, threonine, asparagine, valine, glycine and methionine. None of the residues is a D-amino acid.

Two points matter in the lab. There is no cysteine, so the peptide forms no disulfide bonds and stays a single linear chain. The chain holds two tyrosine residues and no tryptophan, which decides how it is detected on HPLC.

What are the molecular formula and molecular weight of Sermorelin?

The formula counts 149 carbon, 246 hydrogen, 44 nitrogen, 42 oxygen and 1 sulfur atom. The average molecular weight is about 3357.9 g/mol. Our product pages show 3357.958; small differences between sources come from rounding.

The monoisotopic mass is 3355.82 Da. It counts only the most common isotope of each element, so it is slightly lower than the average weight. A mass spectrum is checked against that figure, or against the average weight, depending on how the laboratory reports it.

Both figures describe the peptide alone. Synthetic peptides are often supplied as a salt, commonly acetate or trifluoroacetate, and the powder also holds some water. The mass of powder in a vial and the mass of peptide are therefore not the same number.

What should Sermorelin look like on an analytical report?

TestWhat it confirmsWhat to expect for this sequence
Mass spectrometry, when reportedIdentityA figure that fits the peptide, monoisotopic or average. Calculated electrospray ions: about m/z 1119.61 (three charges), 839.96 (four charges) and 672.17 (five charges)
HPLC with UV detectionPurityOne dominant peak, read at about 214 to 220 nm. Sermorelin absorbs only weakly at about 280 nm
Content, when reportedAmount of peptide in the vialA figure in mg to compare with the size on the label
Net peptide content, when reportedShare of the powder that is peptideA percentage below 100, because salt and water are part of the powder
AppearancePhysical formLyophilized powder. Our product pages describe a solid, white powder

The report for the lot in hand is the source of truth. Posted reports are on the Certificates of Analysis page.

How should lyophilized Sermorelin be stored?

The listings are 5 mg and 10 mg of lyophilized powder, each in a 3 mL vial. Our product pages give storage at 6°C or below, away from heat, light and moisture. Keep the vial sealed between openings.

What should a researcher check?

  • Name and size. The compound and size on the report match the label.
  • Lot number. The lot or batch on the vial is the one on the report.
  • Purity. The report gives an HPLC purity figure for that lot.
  • Mass, where the report gives one. It agrees with the values in the table above.

Research compound in this article

Sermorelin

Lyophilized powder · Choose a size to add to cart:

Research-use note

All NexXGen Peptides compounds are intended strictly for in-vitro research, laboratory and analytical purposes. They are not for human or animal use and must be handled only by qualified researchers aged 21 or older. Nothing in this article is medical advice.

Frequently asked questions

How many amino acids are in Sermorelin?

Twenty-nine. Fifteen different amino acids make up the chain, because nine of them appear more than once.

What is the CAS number for Sermorelin?

86168-78-7.

Is Sermorelin the same compound as CJC-1295 no DAC?

No. Both are chains of 29 amino acids, but they are different compounds with different identifiers. Their sequences differ at positions 8, 15 and 27, where Sermorelin has asparagine, glycine and methionine and CJC-1295 no DAC has glutamine, alanine and leucine. At position 2, Sermorelin has alanine and CJC-1295 no DAC has D-alanine. CJC-1295 no DAC has the formula C152H252N44O42, a molecular weight of about 3367.9 g/mol and the CAS number 863288-34-0.

Can Sermorelin be read at 280 nm on HPLC?

Only weakly. Sermorelin has two tyrosine residues and no tryptophan, so its signal there is weak. Detection can rely on the peptide bonds, which absorb at about 214 to 220 nm.

Does Sermorelin contain disulfide bonds?

No. The sequence has no cysteine, so the peptide is one linear chain.

Browse all research compounds →